Independent Burbank Building Inspections — Brisbane & SEQ
Building with Burbank? VG Inspect provides an independent, QBCC-licensed inspection at each stage so the home and the inclusions you paid for are all there, and built to standard, at handover.
Book an InspectionFrom $660 (new homes under 220m²) — larger homes quoted on request · Same-week availability · Same-Day Digital Reports
Last updated: May 2026
Building with Burbank? An independent set of eyes
Burbank is a national volume builder active across South East Queensland's growth corridors, delivering value-focused single and double-storey designs with a defined inclusions list. They build strongly through the western Ipswich corridor and into the northern Moreton Bay corridor, and maintain a display presence at Kinma Valley in Morayfield [ADAM TO CONFIRM: Burbank display home at Kinma Valley]. VG Inspect works alongside Burbank owners as a fully independent inspector — we are not engaged or paid by any builder. Our role is to give you an additional, owner-focused set of QBCC-licensed eyes that complements Burbank's own quality assurance and the private certifier's regulatory checks. Every item we note is photographed and referenced to the National Construction Code (NCC Volume 2), the relevant Australian Standards or the QBCC Standards and Tolerances Guide.
What VG Inspect commonly checks on a Burbank build
With Burbank's volume model and defined inclusions list, we pay particular attention to confirming the specified inclusions are actually installed and to the detailing on whichever cladding system your design uses. Stage by stage:
Pre-pour & slab stage
- Slab dimensions, edge beams and reinforcement cover against the engineer's design and AS 2870 for the lot's soil class — important across the reactive clays of the Ipswich and Moreton Bay corridors.
- Termite management system per AS 3660.1, and set-down levels at wet areas and the garage.
- Vapour barrier integrity, laps and penetrations before the pour.
- Site cut, fill compaction and drainage set-out relative to the natural fall of the block.
Frame stage
- Wall frames, roof trusses, bracing and tie-downs per AS 1684 and the truss layout, checked before linings and cladding close them in.
- Lintels and openings sized and supported correctly for the cladding system above.
- Window and door openings square and plumb ready for fit-off.
- Wind classification under AS 4055 confirmed for the fixing schedule on exposed lots.
Cladding & lock-up
- Brick veneer coursing, articulation (control) joints and weep holes at the correct spacing, or render substrate and lightweight cladding detailing depending on your design.
- Window head and sill flashings, sealants and clean cavities behind the cladding.
- Roof covering, flashings, valleys and penetrations per NCC Volume 2 Part 3.5.
Waterproofing & fixing
- Wet-area waterproofing to showers, bathrooms and laundry per AS 3740 before tiling — the highest-consequence defect category on any build.
- Plasterboard, cornice and trim set-out, plus cabinetry alignment and door/drawer operation.
- Tiling layout, lippage and grout against the relevant tolerances and the contract finishes.
PCI / handover
- Internal finishes — plaster, paint, tiling and grout — against QBCC Section 14 tolerances viewed from 1.5 m in natural light.
- Every contract inclusion checked off against your specification — fixtures, tapware, appliances and the finishes you actually paid for.
- Site works, driveway, drainage falls and finished ground levels per NCC Volume 2 Part 3.1.2.3.
- Compliance documentation collated — Form 16s, Form 21, waterproofing and termite notices.
See how a handover inspection works on a new build — PCI / handover inspection.
Suburbs where we inspect Burbank homes
VG Inspect carries out independent inspections alongside Burbank owners right across the northern Moreton Bay growth corridor and the wider South East Queensland market. A few of the suburbs and estates we cover:
Not sure if we cover your estate or stage? Book online or call us — 07 3180 8041 — and we'll confirm before charging anything.
Why an independent inspection alongside Burbank
Bringing in an independent inspector is not about doubting Burbank — it is simply good practice for a purchase this size. A national volume builder runs many sites at once, and the private certifier signs off regulatory compliance rather than finish quality or whether each contract inclusion is present. A VG Inspect report fills that gap with a clear, photographed, standards-referenced list your site supervisor can work through quickly. In our experience builders, Burbank included, would far rather rectify a flagged item before handover than carry it into the warranty period. A fair, professional report is therefore a help to everyone involved — owner, builder and supervisor alike — and that collaborative approach is how we work across South East Queensland.
Inspection types for Burbank builds
Burbank inspection FAQs
Is VG Inspect connected to Burbank?
No — we are fully independent. We are not engaged, paid or appointed by Burbank or any builder. You are our only client, which is what allows us to give you a frank, standards-based view of your new home.
What do you look at most closely on a Burbank build?
Because Burbank works to a defined inclusions list, we pay close attention to confirming each specified inclusion is actually installed, alongside wet-area waterproofing and the detailing of whichever cladding system your design uses — brick veneer, render or lightweight cladding.
Does Burbank have a display home in the Moreton Bay corridor?
Burbank maintains a display presence at Kinma Valley in Morayfield [ADAM TO CONFIRM: Burbank display home at Kinma Valley]. Wherever your build is, we inspect on your own block rather than the display — the inspection is always specific to your home and its lot.
Should I inspect earlier stages or just the handover?
The PCI / handover inspection is the most important single inspection. Adding a frame and a lock-up/waterproofing inspection is valuable too, because framing and waterproofing are hard to assess once they are closed in or tiled over.
Will an independent report upset my Burbank supervisor?
It shouldn't. A photographed, clause-referenced report is easy for a supervisor to action, and most builders prefer to rectify an item before handover rather than after. We keep everything factual and professional, and the report is yours.
When should I book my Burbank handover inspection?
Book as soon as Burbank issues the practical completion notice — typically 5 to 14 days before handover. Booking early protects your slot and leaves room for a re-inspection after any rectification.
How much does a Burbank inspection cost?
Practical completion / handover inspections are $660 for new homes under 220m² (larger homes quoted on request). Stage inspections and 11-month warranty inspections start from $550, with no travel surcharge across the SEQ growth corridors.
Which areas do you cover for Burbank?
We inspect Burbank builds throughout South East Queensland, including Caboolture, Morayfield, Kinma Valley, Lilywood and Lilywood Landings, plus the Ipswich-side corridor of Springfield Lakes, Ripley, Spring Mountain and Redbank Plains. Not sure if we reach your estate? Give us a call and we will confirm first.
Book your independent Burbank inspection
Building with Burbank? Have an independent, QBCC-licensed inspector (Licence 1318443) on your side before handover. Book online or call 07 3180 8041 — same-week availability across South East Queensland.
Book an Inspection