Frame Inspection in Bellmere
The frame inspection is your last clear view of the structural skeleton of your new Bellmere home before insulation, plasterboard and cladding cover it. VG Inspect carries out an independent, QBCC-licensed frame inspection once the wall and roof framing is up and the roof is on — checking framing members, tie-downs, bracing, truss connections and service penetrations against AS 1684, the site wind classification under AS 4055 and the engineer's design. Every item is photographed and referenced in a same-day digital report you can give straight to your builder. Across Bellmere's growing family estates, the frame stage is one of the most worthwhile inspections to book, because it is the only time the structure is fully visible before the trades close it all in.
Book an InspectionFrame Inspection from $550 · Same-day digital report · QBCC Licence 1318443 · Call 07 3180 8041
Last updated: May 2026
Why a frame inspection matters in Bellmere
Once the plasterboard, insulation and cladding go on in your Bellmere home, the frame, its tie-downs and bracing are hidden for good. The frame stage is the only practical chance to confirm the structural connections that hold the roof down in a wind event and carry the building's loads are all present and correctly fixed. A missed bracing panel, an under-nailed tie-down strap or an over-cut structural member is straightforward to put right while the frame is open, but a much larger job once it is lined. On a home anchored to a slab designed for reactive Bellmere soil, a sound load path from roof to footing matters all the more. An independent frame inspection gives you confidence the bones of the home are right before the finishes cover them.
Local conditions in Bellmere (4510)
Bellmere sits in the inland, relatively open country west of Caboolture, where lots are assigned a site wind classification under AS 4055 that sets the bracing and tie-down requirements in AS 1684. On these affordable family estates the frame stage is the first time the home's full structure is on show, so it is worth confirming the tie-down load path and bracing match the engineering for your particular design. The single-storey and two-storey homes common across Bellmere each carry loads down through the frame to the slab, and on reactive-soil sites that complete, properly connected load path is what ties the structure to a slab designed for ground movement — well worth verifying before linings hide it.
What we check at the frame stage
The frame inspection happens once the wall and roof framing is up and the roof is on, but before insulation, plasterboard or cladding cover it. This is the last chance to see the structural skeleton of the home before it is hidden. Here is what we check against AS 1684, the engineer's design and the National Construction Code:
Structural framing
- Wall frames, studs, top and bottom plates, lintels and openings checked for size, spacing and straightness against AS 1684 and the approved plans.
- Roof trusses, their layout, bearing and on-site modifications checked against the truss manufacturer's documentation.
- Bearers, joists and any steel members or posts confirmed correctly sized and supported.
Tie-down & bracing
- Tie-down and hold-down connections (straps, bolts, brackets) checked through the load path for the lot's wind classification under AS 4055 / AS 1684.
- Wall and roof bracing installed, fixed and at the quantities the engineering requires.
- Truss-to-wall and wall-to-slab connections confirmed before they are covered.
Penetrations & set-out
- Service penetrations and notching checked so plumbing and electrical runs have not over-cut structural members.
- Window and door openings confirmed square, plumb and correctly sized for fit-off.
- Frame straightness and plumb documented before linings lock it in.
Every item is photographed and referenced to the relevant Australian Standard, NCC clause or the QBCC Standards and Tolerances Guide, then delivered in a same-day digital report you can hand straight to your builder. See the full construction stage inspection process, or the PCI / handover inspection for the final stage before you accept the keys.
Other inspection stages in Bellmere
Most owners book several stages across the build so defects are caught before the next trade covers them. Alongside the frame inspection, we also inspect:
Inspection pricing in Bellmere
Frame Inspection FAQs — Bellmere
When is the right time for a frame inspection in Bellmere?
Once the wall frames and roof trusses are up, the roof is on, and the frame is complete — but before insulation, wraps and plasterboard start going on. That window lets every structural member and connection be seen and checked while it is still fully accessible.
What does the frame inspection cover?
Wall and roof framing member sizes, spacing and straightness against AS 1684, roof truss layout and connections, tie-down and hold-down fixings through the load path for the lot's wind classification under AS 4055, wall and roof bracing, and any service penetrations or notching that could compromise structural members.
Do you inspect two-storey frames in Bellmere?
Yes. Two-storey and larger designs concentrate load through the lower-level frame down to the footings, so particular attention is paid to load paths, lintels, stair framing and upper-floor support before they are covered. The same AS 1684 and engineering checks apply, with extra focus on the higher-load connections.
How much is a frame inspection in Bellmere?
Frame inspections are from $550 with a same-day digital report and no travel surcharge across Bellmere and the wider Moreton Bay Regional Council area. It is one of the highest-value stage inspections because the structure is only ever fully visible once.
Your inspector
Every Bellmere inspection is carried out personally by Adam Gates, an independent QBCC-licensed building inspector (Licence 1318443). Nothing is subcontracted — the person who licences and signs your report is the person who stood on your site. You can verify the licence yourself on the QBCC online licence search before you book. VG Inspect holds a 5.0 rating across 65 verified reviews and is fully insured.
Book your Bellmere frame inspection
Same-week availability · QBCC licensed · Same-day digital reports.
Book an InspectionCall Adam on 07 3180 8041 — Frame Inspection from $550.