Frame Inspection in Caboolture
The frame inspection is your last clear view of the structural skeleton of your new Caboolture home before insulation, plasterboard and cladding cover it. VG Inspect carries out an independent, QBCC-licensed frame inspection once the wall and roof framing is up and the roof is on — checking framing members, tie-downs, bracing, truss connections and service penetrations against AS 1684, the wind classification under AS 4055 and the engineer's design. Every item is photographed and referenced in a same-day digital report you can give straight to your builder. Across Caboolture's busy new-home market, where many homes are going up at once, the frame stage is one of the most worthwhile inspections to book before the trades close it all in.
Book an InspectionFrame Inspection from $550 · Same-day digital report · QBCC Licence 1318443 · Call 07 3180 8041
Last updated: May 2026
Why a frame inspection matters in Caboolture
Once the plasterboard, insulation and cladding go on in your Caboolture home, the frame, its tie-downs and bracing are hidden for good. The frame stage is the only practical chance to confirm the structural connections that hold the roof down in a wind event and carry the building's loads are all present and correctly fixed for the lot's wind classification. A missed bracing panel, an under-nailed tie-down strap or an over-cut structural member is straightforward to put right while the frame is open, but a far bigger job once it is lined and finished. An independent frame inspection against AS 1684 and the engineering gives you confidence the bones of the home are right before the finishes hide them — and a clear photographed record if anything needs to be actioned.
Local conditions in Caboolture (4510)
Caboolture sits in the inland Moreton Bay area where each lot is assigned a site wind classification under AS 4055 that drives the bracing and tie-down requirements in AS 1684. On a new build the frame is the first time the home's full structure is visible, and with a large volume of construction across the town's estates and infill sites, it is worth confirming the tie-down load path and bracing match the engineering for your specific design. Many of Caboolture's new homes are single and double-storey project designs that concentrate load through the lower frame and connections, so we pay close attention to those load paths, lintels and bracing panels before they are permanently covered.
What we check at the frame stage
The frame inspection happens once the wall and roof framing is up and the roof is on, but before insulation, plasterboard or cladding cover it. This is the last chance to see the structural skeleton of the home before it is hidden. Here is what we check against AS 1684, the engineer's design and the National Construction Code:
Structural framing
- Wall frames, studs, top and bottom plates, lintels and openings checked for size, spacing and straightness against AS 1684 and the approved plans.
- Roof trusses, their layout, bearing and on-site modifications checked against the truss manufacturer's documentation.
- Bearers, joists and any steel members or posts confirmed correctly sized and supported.
Tie-down & bracing
- Tie-down and hold-down connections (straps, bolts, brackets) checked through the load path for the lot's wind classification under AS 4055 / AS 1684.
- Wall and roof bracing installed, fixed and at the quantities the engineering requires.
- Truss-to-wall and wall-to-slab connections confirmed before they are covered.
Penetrations & set-out
- Service penetrations and notching checked so plumbing and electrical runs have not over-cut structural members.
- Window and door openings confirmed square, plumb and correctly sized for fit-off.
- Frame straightness and plumb documented before linings lock it in.
Every item is photographed and referenced to the relevant Australian Standard, NCC clause or the QBCC Standards and Tolerances Guide, then delivered in a same-day digital report you can hand straight to your builder. See the full construction stage inspection process, or the PCI / handover inspection for the final stage before you accept the keys.
Other inspection stages in Caboolture
Most owners book several stages across the build so defects are caught before the next trade covers them. Alongside the frame inspection, we also inspect:
Inspection pricing in Caboolture
Frame Inspection FAQs — Caboolture
When is the right time for a frame inspection in Caboolture?
Once the wall frames and roof trusses are up, the roof is on, and the frame is complete — but before insulation, wraps and plasterboard start going on. That window lets us see every structural member and connection while it is still accessible and able to be photographed for your report.
What does the frame inspection cover?
Wall and roof framing member sizes, spacing and straightness against AS 1684, roof truss layout and connections, tie-down and hold-down fixings through the load path for the lot's wind classification under AS 4055, wall and roof bracing, and service penetrations or notching that could compromise structural members.
Do you inspect two-storey frames in Caboolture?
Yes. Two-storey and larger designs concentrate load through the lower-level frame and footings, so we pay particular attention to load paths, lintels, stair framing and upper-floor support before they are covered. The same AS 1684 and engineering checks apply, with extra focus on the higher-load connections.
How much is a frame inspection in Caboolture?
Frame inspections are from $550 with a same-day digital report and no travel surcharge across Caboolture and the wider Moreton Bay Regional Council area. It is one of the highest-value stage inspections because the structure is only fully visible once before the linings go on.
Your inspector
Every Caboolture inspection is carried out personally by Adam Gates, an independent QBCC-licensed building inspector (Licence 1318443). Nothing is subcontracted — the person who licences and signs your report is the person who stood on your site. You can verify the licence yourself on the QBCC online licence search before you book. VG Inspect holds a 5.0 rating across 65 verified reviews and is fully insured.
Book your Caboolture frame inspection
Same-week availability · QBCC licensed · Same-day digital reports.
Book an InspectionCall Adam on 07 3180 8041 — Frame Inspection from $550.